WIKIABOUT

FOR TIPS, gUIDES & TUTORIALS

subscribe to our Youtube

GO TO YOUTUBE

14455 questions

17168 answers

28195 comments

0 members

Most popular tags

rut955 rut240 rut950 rutx11 rms vpn to openvpn wifi not sms trb140 firmware connection - ipsec on rutx12 rutx09 modbus
We are migrating to our new platform at https://community.teltonika.lt. Moving forward, you can continue discussions on this new platform. This current platform will be temporarily maintained for reference purposes.

RUTX11, Firmware: RUTX_R_00.02.00, Wirelles problems

0 votes
2,368 views 5 comments
by anonymous

RUTX11 restored to default settings.

1. After wizard 2.4 and 5Ghz as AP works properly.

2. Added new 5GHz interface as Client (station mode)

  • scanned, choosed SSID
  • then changed GeneralSetup->Channel to Auto
  • Changed AdvancedSettings->CountyCode to PL (00-World the same effects)
  • ESSID my ssid name
  • BSSID cleared because I want to roaming between APs with the same SSID
  • Save&Apply
  • wifi connected to the BSSID but local AP does not works

BTW:
    Marked BSSID is not a real BSSID, it's always MAC address local wlan1 interface:

Link to troubleshoot file: https://drive.google.com/open?id=1V_n535q9ECrULfGiETwpwAvfkg82SNmD

3. When I choose for 5GHz Channel=100 (I know my SSID is on it)

  • Save
  • then Save&Apply i got this:
  • after /etc/init.d/network restart and wait about 1-2minutes i got this:
  • but iwconfig says:
  • and ofcourse local AP (RUT_F680_5G) is not visible for the clients:

 BTW:
    For all interfaces in AP mode signal strength is always zero:

Link troubleshoot file: https://drive.google.com/open?id=1ZtWMTNWzyFNGawEyIKdqfEQ_n_qdI6qL

4. I had few times situation when I can not connect to AP in station mode even after reboot. And other situations like for example this:

I can not reproduce those situations right now.

For me version RUTX_R_00.02.00 right now is more unstable than before.

Questions:

  1. Will wpa_supplicant option bgscan will/should work? If yes where can I write this option? When I put it to /etc/config/wirelles the option not moving to wpa_supplicant.config
  2. After switch to mac80211 WiFi driver the wpa_cli command disappeared. Will you plan restore this command? I was planning test: "wpa_cli [options] roam BSSID"

Why I asked. We want to install RUTX11 in our Automated Guided Vehicle that will drive in the factory, so we need fast (as possible) roaming between APs

Regards

2 Answers

0 votes
by anonymous
Good day,

The points that you have raised are being analyzed.

Would expect an update mid-next week.

If in the meantime you have more comments or observations - please do not hesitate to inquire.

Otherwise - thank you for your patience. Once i have an update - shall provide it to you here.

Regards,

Simon
by anonymous
Hello,

I have also the  problem after updating to RUTX11 Firmware RUTX_R_00.02.00.1 my wifi settings are gone.

If I go back to RUTX_R_00.01.06 wifi is working and Blutooth is missing.

Here is a part what dmesg says:

ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2

[   27.502997] ath10k_ahb a000000.wifi: Falling back to user helper

[   35.889990] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2

[   35.890036] ath10k_ahb a000000.wifi: Falling back to user helper

[   35.950038] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed

[   37.027313] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000

[   37.027360] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1

[   37.039071] ath10k_ahb a000000.wifi: firmware ver 10.4-3.5.3-00057 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6a15d64d

[   37.085388] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA4019/hw1.0/board-2.bin

[   37.085566] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2

[   37.100600] ath10k_ahb a000000.wifi: Falling back to user helper

[   37.140214] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed

[   37.140456] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0

[   37.147831] ath10k_ahb a000000.wifi: failed to fetch board file: -11

[   37.157187] ath10k_ahb a000000.wifi: could not probe fw (-11)

[   37.342317] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2

[   37.342362] ath10k_ahb a800000.wifi: Falling back to user helper

[   38.600215] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2

[   38.600259] ath10k_ahb a800000.wifi: Falling back to user helper

[   38.663471] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed

[   38.665275] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000

[   38.671396] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1

[   38.684221] ath10k_ahb a800000.wifi: firmware ver 10.4-3.5.3-00057 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6a15d64d

[   38.729910] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA4019/hw1.0/board-2.bin

[   38.730042] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2

[   38.745112] ath10k_ahb a800000.wifi: Falling back to user helper

[   38.795274] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed

[   38.795560] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0

[   38.802871] ath10k_ahb a800000.wifi: failed to fetch board file: -11

[   38.812255] ath10k_ahb a800000.wifi: could not probe fw (-11)

Best Regards
by
Hello,

any updates ? Without the wifi, router rutX11 is practically useless for me.

thanks,

-C
by

Same for me - no wifi interfaces:

by anonymous
Hello,

please contact me via Private Message, I would like to organize a remote session to fix this issue.
0 votes
by anonymous
Hello,

Firmware version RUTX_R_00.02.00.2 was recently released which fixes WiFi issue, please upgrade.

You can find newest firmware here: https://wiki.teltonika.lt/view/RUTXxx_Firmware
by anonymous

Thanks for 2.00.2. It works better. But I have still issue with this version.

Steps to reproduce:
1. No wwan interfaces for 5GHz
2. Add interface as Client Mode:

3. RUTX11 connected to SSID:


BSSID is still incorrect. For me (for ClientMode) should be BSSID of connected AccessPoint

4. Add new virtual interface as AP
5. 5GHz wireless stop working:

6. Link to troubleshoot file: https://drive.google.com/open?id=1xjsOpFdlhYge1SHgHU3u32T5ceaFpykZ


What about my previous questions?
1. Will wpa_supplicant option bgscan will/should work? If yes where can I write this option? When I put it to /etc/config/wirelles the option not moving to wpa_supplicant.config
2. After a switch to mac80211 WiFi driver, the wpa_cli command disappeared. Will you plan to restore this command? I was planning test: "wpa_cli [options] roam BSSID"